#68 Article 11376 Posted at 1997/08/05 15:37:34 by teto (MAP542) [MODEM]
Subject: Re:*8 モデム接続試験のお願い /2903(#2) .... /2895(#2) /2893(#2)
tetoです。 #2 system Q & A から ちょっとずれるから #68 computer です。 ttya5の初期化コマンドだそうですが、、 マニュアル(PDFファイル）から 該当部分を切り出してきました。 %C3&k3N1\N3&Q5は 工場出荷時と 同じですね。 AT&F\A3%C3&C1&D2&K3L0M0N1\N3&Q5&S0W2S0=1\J0 &F AT&F Recalls factory defaults. Instructs the modem to use the factory set parameters. \A3 Maximum MNP Block Size. Use this command to transmit smaller blocks of data in a reliable data link connection. AT\A0 set maximum block size to 64 characters. AT\A1 set maximum block size to 128 characters. (DEFAULT) AT\A2 set maximum block size to 192 characters. AT\A3 set maximum block size to 256 characters. %C3 Compression Control. Determines whether or not modem will use data compression. AT%C0 disables data compression AT%C1 enables MNP5 data compression negotiation AT%C2 enables V42bis data compression AT%C3 enables both V.42bis and MNP5 data compression (DEFAULT) &C1 Data carrier detect (DCD) signal AT&C0 Forces DCD signal to be on at all times. (default) AT&C1 DCD on indicates presence of data carrier. &D2 Data terminal ready (DTR) signal. Interprets the ON to OFF transition of the DTR signal from the DTE according to the &Q settings. AT&D0 &Q0,5,6. DTR ignored. &Q1,4. Modem hangs up; auto answer not affected. &Q2,3. Modem hangs up; auto answer inhibited. (default) AT&D1 &Q0,1,4-6. Asynchronous escape sequence. &Q2,3. Modem hangs up; auto answer inhibited. AT&D2 &Q0-6. Modem hangs up; auto answer inhibited. AT&D3 &Q0,1,4-6. Modem does a soft reset as if the ATZ command were received; &Q2,3. Modem hangs up; auto answer inhibited. &K3 DTE/Modem flow control AT&K0 Disable flow control. AT&K3 Enable RTS/CTS (default for data mode) AT&K4 Enable XON/XOFF. AT&K5 Enable transport XON/XOFF. AT&K6 Enable both RTS/CTS and XON/XOFF (default for FAX mode) L0 Speaker volume ATL0 Low volume. ATL1 Low volume. (default) ATL2 Medium volume. ATL3 High volume. M0 Speaker control ATM0 Disables the modem speaker. ATM1 Turns speaker on until carrier has been detected. (default) ATM2 Speaker is always on. ATM3 Speaker is on when receiving carrier and during dialing, but off during answering. N1 Automode enable ATN0 Requires speed of the connection be that specified by the value of S37. ATN1 Permits handshaking at any speed supported by both modems. (default) \N3 Error Correction Operating Mode. Selects the operating mode the modem uses while connected. AT\N0 NORMAL (speed buffering) mode. AT\N1 DIRECT (pass-through) mode. AT\N2 RELIABLE LINK mode. Specifies error correction for the modem-to-modem connection AT\N3 AUTO-RELIABLE LINK mode. Attempts error-correction connection but will fall back to normal mode if unable to establish an MNP link. (default) AT\N4 LAPM error correction mode. AT\N5 MNP error correction mode &Q5 Asynchronous mode AT&Q0 Direct Asynchronous mode. AT&Q5 Modem negotiates an error-corrected link. (default) AT&Q6 Selects asynchronous operation in normal mode (i.e. speed buffering). S0 これって意味無し？ W2 Error correction message control ATW0 Error correction call progress not reported. (default) ATW1 Call progress reported. ATW2 Call progress not reported. Connect xxxx message reports DCE speed (e.g., CONNECT 28800). S0=1 Reg. Range Units Default Definition S0 0-255 rings 0 Auto-answer \J0 マニュアルに載ってないけど、、端末速度固定ですね。